wiki:3Dprinting

http://wiki.kinolux.de/filez/img/zgsptze.jpg

This is a notepad and the documentation for my 3D printerstuff.
Currently I am using a Flashforge Creator X printer (stock firmware 7.2) driven by ReplicatorG on OSX.

settings PLA:

  • slicer: skeinforge
  • bed: blue tape
  • feedrate: 70-90mm/s
  • travel feedrate: 90-120mm/s
  • head temp: 190-205 C
  • bed temp: 60 C

todo:

  • retraction
  • dualheaded
  • PLA samples
  • proper feedrate calculation

link collection:


dump:

M126
(<edgeWidth> 0.4 </edgeWidth>)
(<perimeterWidth> 0.4 </perimeterWidth>)
(<profileName> PLA </profileName>)
(<settings>)
(<setting> alteration Activate_Alteration True </setting>)
(<setting> alteration Name_of_End_File:  </setting>)
(<setting> alteration Name_of_Start_File:  </setting>)
(<setting> alteration Remove_Redundant_Mcode True </setting>)
(<setting> alteration Replace_Variable_with_Setting True </setting>)
(<setting> comb Activate_Comb True </setting>)
(<setting> comb Running_Jump_Space_(mm): 2.0 </setting>)
(<setting> cool Activate_Cool True </setting>)
(<setting> cool Bridge_Cool_(Celcius): 1.0 </setting>)
(<setting> cool Orbit False </setting>)
(<setting> cool Slow_Down True </setting>)
(<setting> cool Maximum_Cool_(Celcius): 1.0 </setting>)
(<setting> cool Minimum_Layer_Time_(seconds): 5.0 </setting>)
(<setting> cool Minimum_Orbital_Radius_(millimeters): 10.0 </setting>)
(<setting> cool Name_of_Cool_End_File: cool_end.gcode </setting>)
(<setting> cool Name_of_Cool_Start_File: cool_start.gcode </setting>)
(<setting> cool Orbital_Outset_(millimeters): 2.0 </setting>)
(<setting> cool Turn_Fan_On_at_Beginning True </setting>)
(<setting> cool Turn_Fan_Off_at_Ending True </setting>)
(<setting> dimension Activate_Dimension True </setting>)
(<setting> dimension Absolute_Extrusion_Distance True </setting>)
(<setting> dimension Relative_Extrusion_Distance False </setting>)
(<setting> dimension Extruder_Retraction_Speed_(mm/s): 20.0 </setting>)
(<setting> dimension Filament_Diameter_(mm): 1.75 </setting>)
(<setting> dimension Filament_Packing_Density_(ratio): 0.85 </setting>)
(<setting> dimension Maximum_E_Value_before_Reset_(float): 91234.0 </setting>)
(<setting> dimension Minimum_Travel_for_Retraction_(millimeters): 1.0 </setting>)
(<setting> dimension Retract_Within_Island False </setting>)
(<setting> dimension Retraction_Distance_(millimeters): 0.0 </setting>)
(<setting> dimension Restart_Extra_Distance_(millimeters): 0.0 </setting>)
(<setting> export Activate_Export True </setting>)
(<setting> export Add_Descriptive_Extension False </setting>)
(<setting> export Add_Export_Suffix False </setting>)
(<setting> export Add_Profile_Extension False </setting>)
(<setting> export Add_Timestamp_Extension False </setting>)
(<setting> export Also_Send_Output_To:  </setting>)
(<setting> export Analyze_Gcode True </setting>)
(<setting> export Do_Not_Delete_Comments True </setting>)
(<setting> export Delete_Crafting_Comments False </setting>)
(<setting> export Delete_All_Comments False </setting>)
(<setting> export Do_Not_Change_Output True </setting>)
(<setting> export binary_16_byte False </setting>)
(<setting> export gcode_step False </setting>)
(<setting> export gcode_time_segment False </setting>)
(<setting> export gcode_small False </setting>)
(<setting> export File_Extension: gcode </setting>)
(<setting> export Name_of_Replace_File: replace.csv </setting>)
(<setting> export Save_Penultimate_Gcode False </setting>)
(<setting> fill Activate_Fill True </setting>)
(<setting> fill Diaphragm_Period_(layers): 100 </setting>)
(<setting> fill Diaphragm_Thickness_(layers): 0 </setting>)
(<setting> fill Extra_Shells_on_Alternating_Solid_Layer_(layers): 2 </setting>)
(<setting> fill Extra_Shells_on_Base_(layers): 2 </setting>)
(<setting> fill Extra_Shells_on_Sparse_Layer_(layers): 2 </setting>)
(<setting> fill Grid_Circle_Separation_over_Perimeter_Width_(ratio): 0.2 </setting>)
(<setting> fill Grid_Extra_Overlap_(ratio): 0.1 </setting>)
(<setting> fill Grid_Junction_Separation_Band_Height_(layers): 10 </setting>)
(<setting> fill Grid_Junction_Separation_over_Octogon_Radius_At_End_(ratio): 0.0 </setting>)
(<setting> fill Grid_Junction_Separation_over_Octogon_Radius_At_Middle_(ratio): 0.0 </setting>)
(<setting> fill Infill_Begin_Rotation_(degrees): 90.0 </setting>)
(<setting> fill Infill_Begin_Rotation_Repeat_(layers): 1 </setting>)
(<setting> fill Infill_Odd_Layer_Extra_Rotation_(degrees): 90.0 </setting>)
(<setting> fill Grid_Circular False </setting>)
(<setting> fill Grid_Hexagonal True </setting>)
(<setting> fill Grid_Rectangular False </setting>)
(<setting> fill Line False </setting>)
(<setting> fill Infill_Perimeter_Overlap_(ratio): 0.3 </setting>)
(<setting> fill Infill_Solidity_(ratio): 0.1 </setting>)
(<setting> fill Sharpest_Angle_(degrees): 60.0 </setting>)
(<setting> fill Solid_Surface_Thickness_(layers): 3 </setting>)
(<setting> fill Lower_Left True </setting>)
(<setting> fill Nearest False </setting>)
(<setting> fill Surrounding_Angle_(degrees): 60.0 </setting>)
(<setting> fill Infill_>_Loops_>_Perimeter False </setting>)
(<setting> fill Infill_>_Perimeter_>_Loops False </setting>)
(<setting> fill Loops_>_Infill_>_Perimeter False </setting>)
(<setting> fill Loops_>_Perimeter_>_Infill True </setting>)
(<setting> fill Perimeter_>_Infill_>_Loops False </setting>)
(<setting> fill Perimeter_>_Loops_>_Infill False </setting>)
(<setting> home Activate_Home True </setting>)
(<setting> home Name_of_Home_File: home.gcode </setting>)
(<setting> jitter Activate_Jitter True </setting>)
(<setting> jitter Jitter_Over_Perimeter_Width_(ratio): 2.0 </setting>)
(<setting> raft Activate_Raft True </setting>)
(<setting> raft Add_Raft,_Elevate_Nozzle,_Orbit: False </setting>)
(<setting> raft Base_Feed_Rate_Multiplier_(ratio): 1.0 </setting>)
(<setting> raft Base_Flow_Rate_Multiplier_(ratio): 1.0 </setting>)
(<setting> raft Base_Infill_Density_(ratio): 0.5 </setting>)
(<setting> raft Base_Layer_Thickness_over_Layer_Thickness: 2.0 </setting>)
(<setting> raft Base_Layers_(integer): 1 </setting>)
(<setting> raft Base_Nozzle_Lift_over_Base_Layer_Thickness_(ratio): 0.4 </setting>)
(<setting> raft Initial_Circling: False </setting>)
(<setting> raft Infill_Overhang_over_Extrusion_Width_(ratio): 0.05 </setting>)
(<setting> raft Interface_Feed_Rate_Multiplier_(ratio): 1.0 </setting>)
(<setting> raft Interface_Flow_Rate_Multiplier_(ratio): 1.0 </setting>)
(<setting> raft Interface_Infill_Density_(ratio): 0.5 </setting>)
(<setting> raft Interface_Layer_Thickness_over_Layer_Thickness: 1.0 </setting>)
(<setting> raft Interface_Layers_(integer): 2 </setting>)
(<setting> raft Interface_Nozzle_Lift_over_Interface_Layer_Thickness_(ratio): 0.45 </setting>)
(<setting> raft Name_of_Support_End_File: support_end.gcode </setting>)
(<setting> raft Name_of_Support_Start_File: support_start.gcode </setting>)
(<setting> raft Operating_Nozzle_Lift_over_Layer_Thickness_(ratio): 0.5 </setting>)
(<setting> raft Raft_Additional_Margin_over_Length_(%): 1.0 </setting>)
(<setting> raft Raft_Margin_(mm): 3.0 </setting>)
(<setting> raft Support_Cross_Hatch False </setting>)
(<setting> raft Support_Flow_Rate_over_Operating_Flow_Rate_(ratio): 1.0 </setting>)
(<setting> raft Support_Gap_over_Perimeter_Extrusion_Width_(ratio): 1.0 </setting>)
(<setting> raft None True </setting>)
(<setting> raft Empty_Layers_Only False </setting>)
(<setting> raft Everywhere False </setting>)
(<setting> raft Exterior_Only False </setting>)
(<setting> raft Support_Minimum_Angle_(degrees): 60.0 </setting>)
(<setting> speed Activate_Speed True </setting>)
(<setting> speed Add_Flow_Rate: True </setting>)
(<setting> speed Bridge_Feed_Rate_Multiplier_(ratio): 1.0 </setting>)
(<setting> speed Bridge_Flow_Rate_Multiplier_(ratio): 1.0 </setting>)
(<setting> speed Duty_Cyle_at_Beginning_(portion): 1.0 </setting>)
(<setting> speed Duty_Cyle_at_Ending_(portion): 0.0 </setting>)
(<setting> speed Feed_Rate_(mm/s): 70.0 </setting>)
(<setting> speed Flow_Rate_Setting_(float): 70.0 </setting>)
(<setting> speed Object_First_Layer_Feed_Rate_Infill_Multiplier_(ratio): 0.9 </setting>)
(<setting> speed Object_First_Layer_Feed_Rate_Perimeter_Multiplier_(ratio): 0.9 </setting>)
(<setting> speed Object_First_Layer_Flow_Rate_Infill_Multiplier_(ratio): 0.8 </setting>)
(<setting> speed Object_First_Layer_Flow_Rate_Perimeter_Multiplier_(ratio): 0.9 </setting>)
(<setting> speed Orbital_Feed_Rate_over_Operating_Feed_Rate_(ratio): 0.0 </setting>)
(<setting> speed Maximum_Z_Feed_Rate_(mm/s): 999.0 </setting>)
(<setting> speed Perimeter_Feed_Rate_Multiplier_(ratio): 0.5 </setting>)
(<setting> speed Perimeter_Flow_Rate_Multiplier_(ratio): 0.5 </setting>)
(<setting> speed Travel_Feed_Rate_(mm/s): 90.0 </setting>)
(</settings>)
(<timeStampPreface> 20141101_151927 </timeStampPreface>)
(<procedureName> carve </procedureName>)
(<procedureName> preface </procedureName>)
(<procedureName> inset </procedureName>)
(<procedureName> fill </procedureName>)
(<procedureName> speed </procedureName>)
(<procedureName> raft </procedureName>)
(<procedureName> jitter </procedureName>)
(<procedureName> comb </procedureName>)
(<procedureName> cool </procedureName>)
(<procedureName> dimension </procedureName>)
(<procedureName> alteration </procedureName>)
(<procedureName> export </procedureName>)
(</extruderInitialization>)
(<crafting>)
Last modified 3 years ago Last modified on 11/01/14 15:58:04